For correct,damage-free installation of interference-fit spline halfshafts when doing front wheel bearing service or halfshaft replacement. 62L (1. I read over some old threads recently, and some say 75 lbs and some say 90 lbs for the. Failure to remove vent tube will allow axle fluid to saturate the vent and cause reduced or improper axle venting resulting in axle damage. (It is usually attached to the new half-shaft. Install the. Refer to: Wheel Bearing and Wheel Hub - AWD (204-02 Rear Suspension, Removal and Installation). 5: Identifying Special Tool (204-161) Courtesy of FORD MOTOR CO. NOTE: Carefully align the halfshaft seal with the. I found a pictorial walkthrough on landroveraddict dot com that has good info on the removal but it glosses over. 5. Position the wheel knuckle to the upper arm and loosely install a new nut and bolt. (32 Nm). RH halfshaft. Inspect the differential housing surface for rust, nicks and scratches. Location: Napa California. 2. Inspect the differential side gear splines. 2. Installation 1. To install: Using a new snapring, push the halfshaft into the transaxle until it clicks into position. Front Halfshaft LH (Removal and Installation), Front Halfshaft RH (Removal and Installation). 3. Thread Starter . - Works on Escort/ Lynx,. When installing the driveshaft into the transaxle, use oil seal protector tool KV38105500 or equivalent to protect the oil seal from damage; after installation, remove the tool. I'm not sure but there maybe a difference between the opening diameter on the rotor flange and the half shaft depending on whether it's a 12" vented or non vented rotor. The Fusion and Milan kit includes the halfshaft assembly. 2000-05. Make sure that the washer is fully seated onto the halfshaft. Use Special Service Tool: 205-832 Remover, Halfshaft. 50. 00 Half shaft 1 06506557AA Nut and Washer, Hex Lock, M14 x 1. Secure the drive cup with the included screw pin. Remove the halfshaft oil seal using the special tool. Find your recommended car maintenance schedules, local service centers, warranty advice. Installation Procedure. the correct tool numbers increments around the seal until it is are d93p-1175-a and d93p-1175-b. 2002-) > Ford Workshop Service and Repair Manuals > Mechanical Repairs | 2 Chassis | 205 Driveline | 205-04 Front Drive Halfshafts | Description and Operation | Diagnosis and Testing | Removal and Installation | Disassembly and Assembly |. 11. If equipped with All Wheel Drive, install a new. Install the lower arm pinch bolt and nut. CAUTION: Make sure that the rear halfshaft circlip is installed correctly by pulling the halfshaft gently to make sure it is engaged. Install the. Do not use excessive force when engaging the CV joint into the link shaft. , 205-990 Installer, Axle Seal. Standard halfshaft spline is. Upgraded half shafts are recommended to handle the extreme. Special Tool(s) Front Hub Remover. Front Drive Halfshafts : Escape Hybrid : 2011. NOTE: Fill the rear axle with 0. NOTE: Slide hammer extension may be needed. Pull on the inner joint to make sure it is fully installed. We don't know when or if this item will be back in stock. Check that the snap ring engages correctly. Remove the tools and repeat this procedure to install the remaining rear bushing. 2004-) > Ford Workshop Service and Repair Manuals > Mechanical Repairs | 2 Chassis | 205 Driveline | 205-04 Front Drive Halfshafts | Description and Operation | Diagnosis and Testing | Removal and Installation | Disassembly and Assembly | Front Halfshaft LHInstall the left rear EHD assembly onto the left rear suspension arm. Want Answer 1. (28-36 Nm). Position the special tool over the halfshaft oil seal. FRONT DRIVE SHAFT SUPPORT. Check the transmission fluid fill level. Posted by dminers on Feb 09, 2017. 43. Install the. Install a new snap ring to the halfshaft. NOTE: RH shown; LH similar. The U shaped part of the tool goes over the differential pinion pin and contacts. 3. Install the lower ball joint into the wheel knuckle and install the new lower balljoint bolt and nut. Install front brake anti-lock sensor. $25. D88L-6000-A or equivalent, and attach it to engine hangers. REMOVAL AND INSTALLATION Procedure revision date: 05/21/2002 Halfshaft Special Tool(s) Slide Hammer 100-001 (T50T-100-A) Front Drive Halfshaft Remover 205-241 (T86P-3514-A) Front Hub Remover 205-D070 (D93P-1175-B) or equivalent Installer, Halfshaft 204-161 (T97P-1175-A) or equivalent Removal NOTE: RH shown; LH similar. A/C Clutch Relay. Make sure the CV joint splines are located fully. Remove the two axle shafts. Wrap shop towels around both the inner and outer ON joint boots to avoid damage to the boots during removal and installation. Make sure the CV joint splines are located fully. 5. (80 Nm). 3. Install the halfshaft into the transaxle, being careful not to damage the oil seal. Install a new snap ring to the halfshaft. For damage-free installation of interference-fit spline halfshafts (22 mm) into front hub assemblies. With the halfshaft free at the brake end, use a large common screwdriver or a pry bar to. Install a new halfshaft seal. 2001 Ford Escape. step 7 :Checking the Seals. Tighten lug nuts to 115-142 Nm (85-105 lb-ft). Refer to: Wheel Knuckle - AWD (204-02 Rear Suspension, Removal and Installation). Using the special tool, install the halfshaft outboard end through the wheel bearing and hub assembly. 50 Upper (Halfshaft) 1 68567910AA Snap Ring (Circlip) Axle Shaft 1 68531556AA ORing. 1 Hrs. Using the special tool, separate the halfshaft from the knuckle. Pro. Upgraded half shafts are recommended to handle the extreme. (80 Nm). If the. Special Tool(s): 205-858. Clean the splines on the hub assembly with brake-clean and a wire brush. Push the stub shaft into the transmission so the circlip locks into the differential side gear. Position the ball joint into the wheel knuckle and install the new ball joint pinch bolt and nut. 4. -Can also be used with No. Push on the front washer sleeve to fully seat the washer onto the halfshaft. The three (Torx T55). To install: Using a new snapring, push the halfshaft into the transaxle until it clicks into position. Tighten retaining bolt to 10-14 Nm (89-124 lb-in). Harmonic Balancer Puller Installation Tool For Chevy LS Engine LS1 LS2 LS3 LS6. Check and top off the rear electric drive assembly oil level. 31. lbs. joint boot clamps. Now the OUTER end of the half shaft is freed. Using the special tool, install the damper. Using the special tool, seat the halfshaft splines in the wheel bearing. Tighten to 300 Nm (222 lb-ft). , 205-153 (T80T-4000-W) Handle. Special Tool(s): 205-857. Install a new front wheel hub nut. lbs. Using the Halfshaft Installer, install the outer halfshaft end into the hub assembly. Remove the nut and separate the lower ball joints. Comment; Flag; More. Before I pressed the new joints I thought I would clean it up a little. Using the special tools, remove the rear halfshaft. After the sealant has fully cured, refill the shift-on-the-fly gearbox with SAE 75W-90 GL-5 gear oil. Install the. Halfshaft Installer. , 100-001 (T50T-100-A) Slide Hammer. If necessary: Use a mallet. Remove the special tool. Remove the special tool. Install the Driver Trailing Arm Assembly into the stock location using (1) 7/16” x 4 1/2” Bolt, (1) 7/16” Flat washer. Is it as simple as removing the old and installing the new? Any tricks or suggestions prior to removal and installation? I'm curious about tq settings and things to know before I take. Applications: 1992-newer Ford Probe, 1996-newer Ford Contour/Mercury Mystique, 2000-newer Ford Focus. The tines are thin and the one use bent them. Make sure the CV joint splines are located fully. CAUTION: To avoid to damage halfshaft joints and boots, do not bend the inner halfshaft joint by more. The experts at 1A Auto show you how to replace the CV axle on your 00-07 Ford Taurus. Remove the front wheels and tires. I don’t know if there was a corresponding change in the axle shaft splines length. Remove and discard the nut. Remove the special tool. Arrives by Tue, Nov 7 Buy Bodeman Front Passenger Side CV Axle Half Shaft for 1984-1990 Ford Escort, Ford Tempo and Mercury Topaz at Walmart. 2. Mondeo 2001 (10. Install the halfshaft into the intermediate shaft, if equipped. Clean the seal and lubricate it with fresh gear oil. Using special service tool 205-343 (CV joint boot clamp installer), install the new CV boot clamp. Remove the right side halfshaft from the axle assembly. 00. 160043A 2013-2014 Escape: Replace The Left Hand Halfshaft Seal, Bushing And Halfshaft Assembly If Necessary (Do Not Use With Any Other Labor Operations) 2. Manufacturers Part #: 204-161. (28-36 Nm). 2001 FOA Escape, 12/2000. Remove the transfer case Y bracket retaining bolt. 94. Remove the pinch bolt and nut. NOTE: Start one end of the circlip in the groove and work the circlip over the halfshaft 12. Installation. $20. Make sure the CV joint splines are located fully. You manufacture furniture that you both sell and lease to your customers. Install the halfshaft and axle mounting bracket assembly onto the axle. information, refer to Halfshaft in this section. Position the lower arm into the front wheel knuckle. Use a pry bar to pull out the other end. Using the special tool, disconnect the tie-rod link at the knuckle. 8L and. Get the new axles and install them into the transmission and then into the steering knuckle. Align the splines on the RH halfshaft with the intermediate shaft and push the stub shaft in until the circlip locks the shafts together. Remove the wheel bearing and wheel hub. Same as Ford part numberT97P-1175-A. You may need to remove a split pin holding the nut in place. Now that it's used, it's not returnable. 2000-02. Install the Protector, Half Shaft, Drive 10270 in the differential. Le Mans Master. Separate the lower control arm from the front wheel knuckle. Pull on the inboard CV-joint and remove the right and left halfshafts.